Power 3 Mighty VS7 Power 3 is a professional three-step process to completely clean and revitalize an engine. Step 1 utilizes Mighty VS7 Top Engine Cleaner to remove deposits on intake valves and piston rings. Step 2 utilizes Mighty VS7 Fuel System Cleaner to clean fuel injectors and intake valves. Step 3 utilizes Mighty VS7 Engine Tune Up to restore additives to the engine oil. Features: Helps restore power, performance and mileage Helps pass emissions tests by reducing hydrocarbon, carbon monoxide and nitrogen levels Designed for carburetor or fuel injected engines Produces immediate, noticeable results Benefits: Performing this full service, Mighty VS7 Power 3 will produce noticeable, lasting results. Immediately after service, drivers will notice marked improvements in performance and fuel economy. A decrease in emissions will follow after all of the chemical has been evacuated. Instructions: Step 1 Top End Cleaner. 1) While the engine is still running, remove a vacuum hose from the PCV Valve, brake power booster or highest convenient vacuum hose from the intake manifold (make sure it does not lead through any plastic tees or check valves) and connect the FI01002 (reusable) or the FI1002-D (disposable) feeder kit to the hose making sure the brass valve on the feeder kit is closed. Use CAUTION to make sure the feeder kit hose is clear of the radiator fan and exhaust manifold. 2) Adjust the engine speed to 1200 - 1450 RPM except turbo engines which remain at idle, OR you can leave all vehicles at idle, it takes a little longer. DO NOT RUSH, THIS STEP SHOULD TAKE 6 TO 9 MINUTES ! 3) Connect the #FI01002 (Reusable feeder to hood or under hood latch to support I.V. Bottle) (*Disposable feeder, attatch product bottle to hood) 4) Close the brass valve on Part #FI01002 (Reusable Feeder)and pour entire contents of STAGE #1 Top End Cleaner into the bottle of the part #FI01002 feeder kit bottle. Slowly open the brass valve on the feeder to allow the STAGE 1 cleaner to flow slowly through the vacuum line. (*This Procedure is the same for Disposable feeder) The engine may shake during this process. If the engine should stall, close the brass feeder valve, restart the engine and continue. 5) When the entire contents of the feeder kit or product bottle have been pulled into the engine. Shut off the engine, remove the feeder kit or product bottle, reconnect the vacuum hose and return the engine idle to normal. Step #2: Pour entire contents of #2 Fuel Injector cleaner into fuel tank, with 15 to 20 gallons of fuel in tank. Step #3: Pour entire contents of #3 Anti Friction Oil Additive into engine crakcase ( Add Like Oil into the engine. Copyright 2000-2010, H.D.I. Management Inc. Nevada, USA all rights reserved, All logos, Trademarks, & Copyrights are property of their respective owners. Mighty 2 partInstructions: Step 1 Top End Cleaner. 1) While the engine is still running, remove a vacuum hose from the PCV Valve, brake power booster or highest convenient vacuum hose from the intake manifold (make sure it does not lead through any plastic tees or check valves) and connect the FI01002 (reusable) or the FI1002-D (disposable) feeder kit to the hose making sure the brass valve on the feeder kit is closed. Use CAUTION to make sure the feeder kit hose is clear of the radiator fan and exhaust manifold. 2) Adjust the engine speed to 1200 - 1450 RPM except turbo engines which remain at idle, OR you can leave all vehicles at idle, it takes a little longer. DO NOT RUSH, THIS STEP SHOULD TAKE 6 TO 9 MINUTES ! 3) Connect the #FI01002 (Reusable feeder to hood or under hood latch to support I.V. Bottle) (*Disposable feeder, attatch product bottle to hood) 4) Close the brass valve on Part #FI01002 (Reusable Feeder)and pour entire contents of STAGE #1 Top End Cleaner into the bottle of the part #FI01002 feeder kit bottle. Slowly open the brass valve on the feeder to allow the STAGE 1 cleaner to flow slowly through the vacuum line. (*This Procedure is the same for Disposable feeder) The engine may shake during this process. If the engine should stall, close the brass feeder valve, restart the engine and continue. 5) When the entire contents of the feeder kit or product bottle have been pulled into the engine. Shut off the engine, remove the feeder kit or product bottle, reconnect the vacuum hose and return the engine idle to normal. Step #2: Pour entire contents of #2 Fuel Injector cleaner into fuel tank, with 15 to 20 gallons of fuel in tank. Copyright 2000-2010, H.D.I. Management Inc. Nevada, USA all rights reserved, All logos, Trademarks, & Copyrights are property of their respective owners.